Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Home heating system types and how they work

The most common residential heating systems are split gas furnaces, rooftop gas-electric package units, wall furnaces, floor furnaces, heat pumps, and dual-fuel systems. The U.S. Department of Energy reports that about 65 percent of single-family homes use a central forced-air furnace. Each system heats your house differently, has a different efficiency range, and creates different maintenance needs. Knowing which type you have is the starting point for understanding repair options, replacement decisions, and energy costs.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 8 sections
  1. 01Split gas furnace (forced air)
  2. 02Rooftop gas-electric package unit
  3. 03Wall furnace
  4. 04Floor furnace
  5. 05Heat pump (air-source)
  6. 06Dual-fuel system
  7. 07System type comparison
  8. 08Identifying your system

Split gas furnace (forced air)

A split system is the most common heating setup in the Sacramento region and across the country. The DOE reports that roughly 65 percent of single-family homes in the United States heat with a central forced-air furnace. "Split" means the furnace is one unit (typically indoors) and the air conditioner condenser is a separate unit outdoors. They share a blower and ductwork.

The furnace burns natural gas or propane in a sealed burner chamber. Combustion gases pass through a heat exchanger, warming the metal surfaces. The blower pushes house air across the outside of the heat exchanger, heating the air before it enters the duct system. Combustion exhaust exits through a flue or PVC vent pipe, never mixing with the supply air.

Efficiency is measured as Annual Fuel Utilization Efficiency (AFUE). A standard-efficiency furnace runs at about 80 percent AFUE, meaning 80 cents of every fuel dollar becomes heat and the rest goes up the flue. High-efficiency condensing furnaces reach 90 to 98 percent AFUE by extracting so much heat that the exhaust cools enough to form liquid condensate. The DOE classifies these sealed-combustion condensing units as the safest type for indoor installation because they eliminate the risk of backdrafting combustion gases into the house. For details on how condensing furnaces vent, see our venting guide.

Rooftop gas-electric package unit

A package unit puts the gas furnace, the air conditioner evaporator and condenser coil, and the blower into a single weatherproof cabinet mounted on the roof. Supply and return ducts drop through a roof curb into the house. There is no separate outdoor condenser.

Package units are common on single-story ranch-style homes and manufactured homes throughout the Sacramento Valley. They save indoor floor space because there is no furnace in the attic, garage, or closet. Maintenance and repairs, however, all happen on the roof. Filter access depends on whether the return grille is inside the house or at the unit on the roof.

Efficiency ranges parallel those of split furnaces. You can get a package unit with an 80 percent AFUE furnace section or a 90%+ condensing section. The air conditioning side has its own efficiency rating (SEER2). When it is time to replace a package unit, the entire cabinet is swapped. See our furnace guide for how replacement decisions work across system types.

Wall furnace

A wall furnace is a gas-fired heater recessed into an interior wall, venting directly through the wall behind it to the outside. There is no blower and no ductwork. Heat radiates from the front panel and rises by natural convection. A wall furnace heats the room it faces and maybe adjacent rooms through open doorways, but it does not distribute heat evenly through a whole house.

Wall furnaces were widely installed in Sacramento-area homes built in the 1950s through the 1970s. Many are still in service. They are simple, have few moving parts, and are inexpensive to operate for small spaces. Their efficiency is lower than modern central furnaces, and they provide no air filtration or humidity control.

Modern wall furnaces are direct-vent sealed-combustion units with electronic ignition. Older ones may still have standing pilot lights. If yours has a pilot light, follow the manufacturer's lighting instructions printed on the unit. Never try to modify or relight a pilot that does not respond to those instructions. A wall furnace that smells like gas when it runs or shows a yellow, lazy flame needs professional service.

Floor furnace

A floor furnace sits below the floor, typically between floor joists in a crawl space, with a grille set into the floor above it. Like a wall furnace, it has no blower and no ductwork. Heated air rises through the floor grille by convection, and room air returns to the unit through the same opening.

Floor furnaces were installed in many older Sacramento-area homes, especially those built before the 1960s. They heat the room above them reasonably well but do little for the rest of the house. The floor grille gets hot enough to be a burn hazard for children and pets, and anything dropped through the grille (toys, paper, fabric) becomes a fire risk.

Replacement parts for floor furnaces are increasingly difficult to find. When a floor furnace fails beyond repair, most homeowners switch to a central forced-air system or a wall furnace. That changeover involves adding ductwork or choosing a ductless system, plus a mechanical permit in California.

Heat pump (air-source)

An air-source heat pump works like an air conditioner that can run in reverse. In cooling mode it moves heat from inside the house to the outside. In heating mode it reverses the refrigerant flow and pulls heat from the outdoor air into the house. The DOE notes that modern air-source heat pumps can reduce electricity use for heating by approximately 50 percent compared to electric furnaces and baseboard heaters.

A heat pump does not burn fuel, so there is no combustion, no flue, and no CO risk from the unit itself. Efficiency is measured in HSPF2 (Heating Seasonal Performance Factor) for heating and SEER2 for cooling. Because a heat pump moves heat rather than generating it, it can deliver more heating energy than the electrical energy it consumes.

In the Sacramento Valley, mild winters make air-source heat pumps a strong fit. Overnight lows rarely drop below the mid-30s on the valley floor, well within the range where a modern heat pump operates efficiently. Foothill homes at higher elevations see colder temperatures, where a cold-climate heat pump or a dual-fuel setup makes more sense. Our heat pump vs. furnace comparison covers the crossover point in detail.

Dual-fuel system

A dual-fuel system pairs an air-source heat pump with a gas furnace. The heat pump handles heating in mild weather, where it operates most efficiently. When outdoor temperatures drop below a set switchover point, the system switches to the gas furnace for supplemental heat. This gives you the efficiency of a heat pump most of the time and the capacity of a gas furnace on the coldest nights.

The switchover temperature is typically set between 30 and 40 degrees Fahrenheit, depending on the equipment and local utility rates. In the Sacramento Valley, a dual-fuel system may run on the heat pump for most of the winter and only switch to gas on the coldest mornings. In the foothills, the furnace side sees more use. For sizing considerations, see our crossover temperature guide.

Dual-fuel systems cost more upfront because you are installing two heating sources, but the operating cost can be lower than either system alone if utility rates favor it. SMUD (Sacramento County) and PG&E have different electric and gas rate structures that affect the math. A proper load calculation and rate analysis before installation determines whether the combined system is the right choice for your house.

System type comparison

The table below summarizes how the major heating system types compare on the factors most Sacramento-area homeowners care about.

Residential heating system comparison
System typeFuelEfficiency rangeDuctwork neededBest fit
Split gas furnaceNatural gas or propane80-98% AFUEYesMost homes; available in standard, two-stage, and modulating configurations
Rooftop package unitNatural gas (heat) + electricity (cooling)80-96% AFUE (heat section)Yes (through roof curb)Single-story ranch homes, manufactured homes where indoor space is limited
Wall furnaceNatural gas or propaneLower than central; varies by modelNoSmall homes, single rooms, supplemental heat
Floor furnaceNatural gasLower than central; varies by modelNoOlder homes; mostly legacy installs with limited replacement options
Air-source heat pumpElectricityHigh (moves heat rather than generating it)Yes (or ductless mini-split)Mild climates like the Sacramento Valley; no combustion, no CO risk
Dual fuel (heat pump + furnace)Electricity + natural gas or propaneHigh in mild weather; furnace AFUE when gas runsYesHomes with wide temperature swings; foothills; optimizing operating cost

Identifying your system

If you are not sure what type of heating system you have, here are a few ways to tell. Look at the thermostat: if it has separate heat and cool modes but no "emergency heat" or "auxiliary heat" setting, you most likely have a gas furnace (split or package). If it shows "aux heat" or "emergency heat," you probably have a heat pump, possibly with a gas furnace backup in a dual-fuel setup.

Check the outdoor unit. If there is a large metal cabinet with a fan on top outside your house and a separate furnace indoors, you have a split system. If there is no outdoor unit and the ductwork goes up through the roof to a single cabinet, you have a rooftop package unit. If there is no ductwork at all and heat comes from a wall-mounted panel or a floor grille, you have a wall furnace or floor furnace.

The rating plate on the furnace or outdoor unit lists the model number, fuel type, and capacity. That label is the most reliable identifier. If you are calling for heating service, having the model number ready helps the technician understand what you have before they arrive.

Common questions

What is the most common heating system in Sacramento?

The split gas furnace with a central forced-air duct system is the most common. Rooftop gas-electric package units are a close second, especially in single-story ranch homes. Older homes may still have wall furnaces or floor furnaces.

What is the difference between a split system and a package unit?

A split system has the furnace indoors and the air conditioner condenser outdoors as separate units sharing ductwork and a blower. A package unit combines the furnace, evaporator, condenser, and blower in one weatherproof cabinet on the roof.

Can a heat pump heat a house in Sacramento winters?

Yes. Sacramento Valley overnight lows typically stay in the mid-30s to mid-40s during winter, which is well within the efficient operating range of a modern air-source heat pump. Foothill homes at higher elevations with colder nights may benefit from a cold-climate heat pump or a dual-fuel setup.

What is a dual-fuel system?

A dual-fuel system pairs an air-source heat pump with a gas furnace. The heat pump heats the home in mild weather. When the outdoor temperature drops below a set switchover point, the system automatically switches to the gas furnace. This combines heat-pump efficiency with gas-furnace capacity for the coldest nights.

Are wall furnaces and floor furnaces still safe to use?

A properly maintained wall furnace or floor furnace that is venting correctly is functional, though less efficient than modern central systems. Older units with standing pilots should be inspected annually. Floor furnaces have hot surface grilles that are a burn risk for children and pets. Replacement parts are increasingly hard to find.

How do I know if I have a heat pump or a furnace?

Check your thermostat. If it has an emergency heat or auxiliary heat setting, you likely have a heat pump. If it has only heat and cool modes, you likely have a gas furnace. You can also check the outdoor unit: a heat pump runs in both summer and winter, while an air conditioner condenser only runs in summer.

What does AFUE mean?

AFUE stands for Annual Fuel Utilization Efficiency. It measures how much of the fuel a furnace consumes is converted into heat for your home, expressed as a percentage. An 80 AFUE furnace turns 80 percent of its fuel into heat. A 96 AFUE furnace turns 96 percent into heat and loses only 4 percent through exhaust.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service