Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 6-minute read · Last reviewed October 2026

AC capacitor and contactor failure explained

The run capacitor gives the compressor and condenser fan motor the electrical boost they need to start and run; the contactor is the switch that sends 240-volt power to the outdoor unit when the thermostat calls for cooling. When either fails, the outdoor unit hums without starting, won't come on at all, or won't shut off. Both are among the most common AC repairs — and both are electrical hazards that belong to a technician.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 5 sections
  1. 01What the run capacitor does
  2. 02What the contactor does
  3. 03Symptoms and what they usually point to
  4. 04Why heat wears these parts out
  5. 05Why these aren't DIY repairs

What the run capacitor does

Single-phase motors — the kind in a residential condenser — need help creating the rotating magnetic field that starts and keeps them turning efficiently. The run capacitor supplies that phase shift. Most residential condensers use a dual run capacitor: one can serving both the compressor (the HERM terminal) and the fan motor (the FAN terminal), with a shared common (C) terminal.

Each capacitor is rated in microfarads (µF) and voltage. The microfarad value must match the motor manufacturer's specification within the stated tolerance; the voltage rating (commonly 370 or 440 volts) must be at least as high as the original. A replacement with the wrong value can make motors run hot and shorten their life.

What the contactor does

The contactor is an electrically operated switch. When the thermostat calls for cooling, it sends a 24-volt control signal to the contactor's coil, which pulls the contacts closed and sends line voltage to the compressor and fan.

Every cycle, the contacts close under load and arc slightly. Over thousands of cycles they pit and burn. Pitted contacts can fail to pass enough current (the unit struggles or won't start), or weld themselves closed (the outdoor unit keeps running even after the thermostat is satisfied). Ants and other insects drawn to the contactor can also wedge the contacts open.

Symptoms and what they usually point to

The outdoor unit's behavior narrows the likely cause before a meter ever comes out:

Outdoor-unit symptoms and likely electrical cause
SymptomLikely cause
Unit hums but neither fan nor compressor startsFailed or weak capacitor; possibly a seized motor
Compressor runs but fan doesn't spinFan side of the dual capacitor, or the fan motor itself
Fan spins but compressor doesn't runCompressor side of the capacitor, compressor overload, or the compressor itself
Outdoor unit completely silent, indoor blower runsContactor not closing, tripped breaker or disconnect, control wiring, or a safety switch
Outdoor unit runs even with the thermostat offContactor contacts welded closed
Breaker trips when the unit tries to startFailing capacitor, hard-starting compressor, or shorted motor

Why heat wears these parts out

Capacitors sit inside the condenser's electrical compartment, which bakes on a sun-exposed pad. Heat accelerates the breakdown of the materials inside a capacitor, and its microfarad value drifts downward over time. A capacitor that tests a little low in spring can fail on the first long run of 100°F afternoons, when the motors it serves are also working their hardest.

Contactors wear by cycle count, and summer is when cycle counts are highest. An oversized system that short-cycles wears its contactor faster than a correctly sized one.

A bulging or leaking capacitor can is a visible sign of failure, but a capacitor can also fail with no visible change. Only a meter reading confirms it.

Why these aren't DIY repairs

Capacitors can hold a dangerous charge after the power is off and must be discharged safely before handling. The condenser runs on a 240-volt circuit. The parts are inexpensive, but the risk isn't, and a wrong-value capacitor causes motor damage that costs far more than the part.

There's also a diagnostic reason. A failed capacitor is sometimes a symptom, not the root cause: a compressor that's starting to seize or a fan motor with worn bearings can kill capacitors repeatedly. A technician measures motor amperage after replacement to make sure the new part isn't the next to fail.

Common questions

How do I know if my AC capacitor is bad?

Common signs are an outdoor unit that hums without starting, a fan that doesn't spin while the compressor runs, or a bulged top on the capacitor can. Confirming it takes a meter that reads microfarads, compared against the rating printed on the capacitor.

Can I push the fan blade to start my AC?

We strongly advise against it. Spinning the fan by hand can get it running on a weak capacitor, but it puts your hand inside a unit with 240-volt circuits and a fan that can start at full speed, and it doesn't fix anything. Turn the system off and have the capacitor tested.

Should the capacitor be replaced during maintenance even if it hasn't failed?

Only if testing shows it has drifted outside its rated tolerance. A capacitor measuring well within its rating doesn't need replacing just because of age. A good maintenance visit records the measured value so you can see it trend over time.

Is a hard-start kit a fix for a struggling compressor?

A hard-start kit adds extra starting torque and can help some compressors start more reliably, but it isn't a cure for a compressor that is failing. It's a judgment call that should follow electrical testing of the compressor, not a substitute for it.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service