Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Cameron Park · El Dorado County

Heat pump repair in Cameron Park's electric and propane homes

Statewide HVAC, a CSLB-licensed contractor (#1023360) working from Roseville, repairs heat pumps in Cameron Park, where the usual trouble is a heat pump that has stopped heating while electric strips or a propane furnace keep the house warm at a much higher cost. Behind that we typically find a failed capacitor or fan motor, a defrost fault that lets the outdoor coil ice over, a refrigerant leak, or a reversing valve stuck in cooling.

  • Reviews on Google
  • CSLB #1023360 · C-20 & C-43
  • Roseville office
  • Emergency calls taken after hours
  • Labor warranty on our work
Call (916) 461-3405

Get a quote

Heat Pump Repair in Cameron Park

Address (optional)

By submitting you agree we may contact you by phone (incl. text) and email about your request. Message/data rates may apply. Reply STOP to opt out of texts. See Privacy and Terms.

Heat Pump Repair in Cameron Park · 9 sections
  1. 01Why heat pump failures cost more in Cameron Park
  2. 02What failure looks like in each kind of Cameron Park system
  3. 03When heat pumps here tend to give out
  4. 04Five things to check before booking
  5. 05Ductwork and wiring in 1970s and 1980s houses
  6. 06Manufactured homes
  7. 07Refrigerant leaks and older systems
  8. 08Repair or replace in Cameron Park
  9. 09Who repairs heat pumps in Cameron Park

Why heat pump failures cost more in Cameron Park

Census estimates for 2020–2024 show about 42% of Cameron Park households heating mainly with electricity and about 38% with propane, with only about 9% on PG&E piped gas and about 4% on wood. In a town with that fuel mix, a heat pump is often the main heat source, not a supplement to a gas furnace, and the backup behind it is either electric resistance strips or propane.

Both backups are expensive ways to make heat compared with a working heat pump. That is the central point of heat pump repair here: when the heat pump fails, the house usually stays warm, and the failure shows up weeks later on a PG&E bill or as an early propane delivery. If either one surprises you this winter, check whether the outdoor unit is actually running when the heat is on.

What failure looks like in each kind of Cameron Park system

The same broken part produces different symptoms depending on what sits behind the heat pump.

Heat pump failure symptoms by system type in Cameron Park homes
SystemWhat you notice firstWhat we check first
All-electric: heat pump with strip-heat air handlerHigher electric bill; AUX or EM showing on the thermostat; house warm but slowWhether the outdoor unit runs; capacitor, contactor, compressor start; thermostat mode
Dual fuel: heat pump on a propane furnacePropane use up; furnace running in mild weatherOutdoor temperature sensor, changeover setting, heat pump lockout
Ductless heat pump in a room or additionOne area cold; indoor head blinking an error codeError code, indoor filter and coil, line-set connections
Packaged unit on a manufactured homeWeak airflow at the far end; short cyclingUnder-floor ducts and crossover before the refrigerant side

When heat pumps here tend to give out

NOAA has no climate-normals station in Cameron Park, which sits at about 1,198 feet. Sacramento Executive Airport on the valley floor averages about 15.4 nights a year at or below freezing; Placerville, at about 1,850 feet, averages about 30.0. Nights at or below 20°F are rare at both: 0.0 a year at Sacramento and 0.4 at Placerville. Cameron Park sits between the two.

So a sound heat pump here is seldom overwhelmed by cold. What winter does is add run time. At Placerville, monthly heating degree days rise more than fourfold from October to December, and a heat pump that limped through the end of summer with a weak capacitor or a slow leak often gives out on the first long run of cold nights. Frost is normal on those nights. Trane's homeowner guidance describes defrost cycles that usually last three to five minutes, with steam and the outdoor fan pausing; it says to get service if the unit seems to defrost constantly, or if the cycles grow longer while ice spreads across the coil.

Five things to check before booking

None of these needs tools, and none puts you near refrigerant or high voltage.

  • Thermostat. Heat mode, not Cool or emergency heat. Emergency heat turns the heat pump off on purpose and runs only the backup.
  • Breakers and disconnect. The outdoor unit and the air handler each have a breaker, and the outdoor unit has a disconnect on the wall nearby. Reset a tripped breaker once; if it trips again, leave it off.
  • Filter. Replace it if it's dirty. Low airflow costs heating output and can trip safety controls.
  • Outdoor unit surroundings. Clear leaves, pine needles and anything stored against it. Make sure gutters, roof runoff or sprinklers aren't soaking it on cold nights.
  • Ice. If the coil is a solid block of ice, don't chip it. Switch to emergency heat, or let a dual-fuel furnace carry the house, until it's diagnosed. Our heat pump not heating guide explains how to tell normal frost from a stuck defrost.

Ductwork and wiring in 1970s and 1980s houses

More than half of Cameron Park's homes date from 1970 to 1989, per the Census year-built table, and the median home was built in 1987. Where a heat pump was added to one of those houses later, it usually inherited ducts laid out for hotter furnace air. Heat pump air is warm rather than hot, and Lennox's homeowner guide notes it arrives in larger volume. Original ducts that leak into an attic or crawlspace, or a return that's too small, can make a working heat pump seem weak, and can also cause the indoor coil to ice in summer.

Older homes also tend to have older control wiring. Thermostat wire that was run for a furnace and AC sometimes lacks a spare conductor for the reversing valve or auxiliary heat, and a thermostat replaced without accounting for that can leave a heat pump stuck in cooling or with backup heat that never shuts off. If the problem began right after a thermostat change, tell us.

Manufactured homes

Cameron Park has about 230 manufactured homes, according to the same Census estimates. In these, the heat pump is often a packaged unit or a closet air handler feeding ducts inside the floor. A torn belly duct or a crossover duct that has separated between sections can dump much of the heated air under the home, which shows up as short cycling, weak heat at the far end and sometimes coil icing. We check the duct path before replacing parts. Federal manufactured-home rules require appliances in these homes to be installed according to their listing, so replacement equipment has to be suited to manufactured-home use.

Refrigerant leaks and older systems

A heat pump that is low on refrigerant heats weakly, ices up quickly and runs long. The right repair is finding the leak, not repeatedly adding charge; our refrigerant leak guide covers when a leak is worth fixing. A system from before 2010 may use R-22, which EPA's phaseout schedule stopped producing and importing on January 1, 2020, so a leak on one of those usually leads to a replacement quote. R-410A systems remain repairable with matching parts: EPA states that components used to repair existing systems are not subject to the Technology Transitions refrigerant limits that apply to new systems installed from January 1, 2025.

Repair or replace in Cameron Park

Repair is the sensible call for a capacitor, contactor, fan motor, defrost board, sensor, thermostat wiring or drain. The case for replacement builds with a failed compressor or reversing valve on an older system, an R-22 unit with any refrigerant problem, a second leak, or a system that has needed several major repairs in a few seasons. If you have propane backup, a failed heat pump buys you time to compare. In an all-electric home it doesn't, because every day on strip heat costs money.

A replacement is permitted through the El Dorado County Building Division. If the new outdoor unit will go in a different spot, check the Cameron Park CSD's architectural review requirements first. Our heat pump replacement service outlines the process, the Cameron Park heat pump installation page covers backup-heat choices, ducts and panels for a new system, and the HSPF2 guide explains the heating ratings on a quote.

Who repairs heat pumps in Cameron Park

Statewide HVAC holds Contractors State License Board license #1023360 and serves Cameron Park from its Roseville office. Emergency calls are taken after hours. A heat pump can't run during a PG&E outage or a Public Safety Power Shutoff; if it won't restart once power returns, check the thermostat and breakers, then call. Our heat pump repair page describes the visit, and the Cameron Park overview covers the area. If the propane furnace is what stopped, see furnace repair in Cameron Park. Nearby, compare heat pumps in El Dorado Hills and Placerville. Book through the contact page.

Google reviews

What customers say on Google

Read our reviews on Google

Reviews and ratings shown live from Google Maps.

  • Loading reviews from Google…
Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Owner-operated

Meet Vasiliy.

Vasiliy Bardadin owns Statewide HVAC and works as its lead technician. The company is licensed by the California Contractors State License Board (CSLB #1023360, C-20 and C-43) and runs out of a Roseville office serving the greater Sacramento region.

Owner & Lead Technician
Vasiliy Bardadin
Since 2017
CSLB-licensed

Heat Pump Repair in Cameron Park

What happens after you reach out

  1. 01

    Call or send a request.

    Tell us what the system is doing — not heating or cooling, making noise, won't start. That's enough to begin.

  2. 02

    A technician diagnoses it.

    We inspect the system and show you what we found. No guessing. No parts-cannon. The actual problem, explained plainly.

  3. 03

    You decide what happens next.

    Repair or replace, budget range, timeline. The call is yours — we lay out the options and you choose.

Also in El Dorado County

Heat Pump Repair in nearby cities

Heat Pump Repair in Cameron Park — questions

My thermostat shows AUX almost all the time. What does that mean?

Your backup heat is doing most of the work. That should happen during defrost and on the coldest nights, not all day. Check that the thermostat isn't in emergency heat and that the outdoor unit runs; if it doesn't, the heat pump needs repair.

We have propane backup. How would we even know the heat pump failed?

Watch propane use and the outdoor unit. If the furnace runs on mild days and the outdoor unit stays quiet, the heat pump has likely stopped or its changeover setting is wrong.

Is ice on the outdoor unit normal in Cameron Park?

A light frost that melts off during a short defrost cycle is normal on cold, damp nights. Thick ice that keeps building, or ice that covers the top of the unit, points to a defrost, fan or refrigerant problem.

Can you repair the heat pump on our manufactured home?

Yes. We check the under-floor ducts along with the equipment, since separated ducts are a common cause of weak heat in these homes.

Our heat pump started acting up right after we installed a new thermostat. Could that be the cause?

Yes. Heat pumps need the thermostat to control the reversing valve and backup heat correctly, and older wiring sometimes lacks the conductors a new thermostat expects. A wiring or setup error can leave the system stuck in one mode.

Do heat pump repairs in Cameron Park need a permit?

No, component repairs don't. Replacing the system is permitted through the El Dorado County Building Division.

More questions? See the full Heat Pump Repair service page or everything we do in Cameron Park.

Sources

Heat Pump Repair in Cameron Park?

Diagnosis first — honest options second.

(916) 461-3405Request Service