Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Furnace blower won't shut off: what to check and when to call

The most common reason a furnace blower runs nonstop is the thermostat fan switch set to ON instead of AUTO. In AUTO mode the blower runs only during a heating cycle. If flipping it to AUTO does not stop the fan, the likely causes are a tripped or stuck limit switch, a clogged filter that overheated the furnace, a stuck relay on the control board, or a wiring fault. You can safely check the thermostat, the filter, and the breaker. Anything involving the limit switch, relay, or control board is technician work.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 8 sections
  1. 01How the blower is supposed to work
  2. 02Thermostat fan switch: the most common cause
  3. 03The limit switch
  4. 04Other causes
  5. 05What you can safely check yourself
  6. 06When it needs a technician
  7. 07Why this happens often in Sacramento-area homes
  8. 08Carbon monoxide safety

How the blower is supposed to work

In a normal heating cycle the thermostat calls for heat, the burners light, and the furnace control board waits for the heat exchanger to warm up before it turns on the blower. When the thermostat is satisfied the burners shut off, but the blower keeps running for another one to three minutes to push the remaining heat out of the heat exchanger. Then it shuts off. That cool-down run is called the fan-off delay, and it is normal.

If the blower never stops after that delay, something is telling it to keep running. The fix depends on what that something is.

Thermostat fan switch: the most common cause

Every thermostat has a fan setting with at least two positions: AUTO and ON. In AUTO the furnace control board decides when the blower runs. In ON the blower runs continuously regardless of whether the burners are firing. Trane's troubleshooting guide lists this as the first thing to check when a furnace fan will not shut off.

Look at the thermostat display or slide switch. If it reads ON or CIRC, switch it to AUTO. The blower should stop within a few minutes once the heat exchanger cools. If it does not, the problem is somewhere else.

Some thermostats also have a CIRC (circulate) mode that runs the blower for part of every hour. That can look like a blower that will not shut off if you happen to notice it during a run cycle. Check whether your model has this mode and whether someone turned it on.

The limit switch

The fan limit switch is a temperature-sensitive safety device mounted in or near the heat exchanger. Carrier describes it as a bimetallic element that monitors furnace temperature and controls two things: it turns the blower on when the heat exchanger reaches a set temperature and shuts the gas valve if the exchanger overheats. The blower activation threshold is typically around 130 degrees Fahrenheit, and the safety cutoff is around 200 degrees Fahrenheit.

If the limit switch gets stuck in the closed position, the control board thinks the furnace is still hot and keeps the blower running. If it trips on high temperature and then fails to reset, the blower stays on while the burners stay off. Either way you end up with a fan that will not stop.

Anything beyond checking the filter and registers is technician territory. The limit switch is inside the furnace cabinet near the heat exchanger, and diagnosing it involves electrical testing with the furnace energized.

Other causes

Several things besides the thermostat and limit switch can keep the blower running. The table below sorts them by what you can check yourself versus what needs a technician.

Causes of a furnace blower that will not shut off
CauseWhat you noticeHomeowner check?Typical resolution
Thermostat set to ON or CIRCBlower runs between heating cycles; air from registers is room temperatureYes: switch fan to AUTOSetting change only
Clogged air filterBlower runs, burners cycle off early, supply air very hot then lukewarmYes: pull the filter and replace if dirtyNew filter; if the limit tripped, the blower may run until the exchanger cools
Closed or blocked registers and returnsSame overheating pattern as a clogged filterYes: open all supply registers, clear furniture from return grillesRestore airflow; keep most registers open
Stuck or failed limit switchBlower runs nonstop; burners may not fireNoTechnician tests and replaces the switch
Stuck blower relay on control boardBlower runs even with thermostat disconnectedNoTechnician replaces the relay or the control board
Wiring short or miswireBlower started running after recent work on the thermostat or furnaceNoTechnician traces and corrects the wiring
Thermostat calling for heat continuouslyBlower and burners both run constantly; house may overshoot setpointPartly: check setpoint, try lowering it well below room temperatureIf the furnace stops when the setpoint drops, the thermostat may need replacement or relocation

What you can safely check yourself

These checks do not require opening the furnace cabinet or touching gas or electrical parts:

  • The thermostat fan switch. Set it to AUTO. If your thermostat is programmable or smart, check the schedule and any fan circulation settings that may have been turned on.
  • The air filter. A clogged filter restricts airflow and can trip the high-limit switch, which shuts off the burners but leaves the blower running. Pull the filter and replace it if it is visibly dirty.
  • Supply registers and return grilles. Make sure they are open and not blocked by furniture, rugs, or storage. Closing too many registers raises duct pressure and reduces airflow across the heat exchanger.
  • The error code. Look through the sight window on the blower door for a blinking LED. Count the blinks and match them to the chart on the door. A limit-switch fault code tells you the furnace overheated. Our furnace error code guide explains common patterns.
  • The breaker and furnace power switch. Turning the furnace off at the switch or breaker for 60 seconds and back on resets the control board. If the blower starts running again right away without the burners firing, the problem is likely the relay, limit switch, or wiring.

When it needs a technician

If the blower keeps running after you have set the fan to AUTO, replaced the filter, and confirmed the registers are open, the problem is inside the furnace. A stuck limit switch, a welded relay contact on the control board, or a wiring fault all require someone to work inside the cabinet with line voltage present.

A safety switch that is tripping repeatedly is doing its job. It means the furnace is overheating or detecting a condition that is unsafe for continued operation. Bypassing or jumpering a limit switch so the furnace runs anyway is how heat exchangers crack and carbon monoxide enters the airstream. Never bypass a safety switch. If your furnace repair technician finds a cracked heat exchanger during the diagnosis, our cracked heat exchanger guide covers what that means.

Why this happens often in Sacramento-area homes

Many furnaces in the Sacramento Valley sit in attics, garages, or hallway closets where the filter is easy to forget. A filter that goes unchanged through the mild fall and then faces steady use in December and January can clog fast. When it does, the furnace overheats and the limit switch shuts the burners down while the blower tries to cool the heat exchanger.

Oversized furnaces make the problem worse. The valley's mild winters mean many homes have more furnace capacity than they need, so the heat exchanger gets hotter faster on every cycle. A properly sized system runs longer, gentler cycles that are easier on the limit switch and the exchanger. See our furnace sizing guide for more on how oversizing causes problems.

In the foothills, furnaces run longer during cold snaps. A filter that was marginal at valley temperatures may trip the limit when the furnace runs extended cycles at higher elevations. Checking the filter before the heating season starts, and again mid-season, catches it early. Our heating hub has a seasonal checklist.

Carbon monoxide safety

A blower that runs nonstop by itself is not dangerous. But if the reason is a limit switch that keeps tripping on overheating, the furnace is cycling between hot and cool states repeatedly, and that stresses the heat exchanger over time. A cracked heat exchanger can allow combustion gases into the supply air.

The U.S. Consumer Product Safety Commission recommends CO alarms on every level of the home and outside sleeping areas, ideally interconnected. CPSC lists the symptoms of CO exposure as headache, dizziness, weakness, nausea, vomiting, sleepiness, and confusion. If a CO alarm sounds or people in the house show those symptoms while the furnace is running, get everyone outside and call 911 from outside. Do not restart the furnace until it has been inspected.

Common questions

Is it bad if my furnace blower runs all the time?

If the thermostat fan is set to ON, the blower running continuously is by design and just uses extra electricity. If the fan is set to AUTO and the blower still will not stop, something is wrong, usually a tripped limit switch, stuck relay, or clogged filter. Get it diagnosed before the underlying cause damages the heat exchanger.

What does the fan limit switch do on a furnace?

It monitors the temperature inside the furnace. It turns the blower on when the heat exchanger is warm enough to deliver heated air, turns the blower off after the exchanger cools at the end of a cycle, and shuts down the gas valve if the furnace overheats. Carrier publishes typical activation around 130 degrees Fahrenheit and a safety cutoff around 200 degrees Fahrenheit.

Can a clogged filter cause the furnace fan to run nonstop?

Yes. A clogged filter restricts airflow across the heat exchanger, the exchanger overheats, and the high-limit switch shuts off the burners. The blower keeps running to cool the exchanger down. If the filter stays clogged, the cycle repeats and the blower may seem like it never stops.

How do I turn off a furnace blower that will not stop?

First, set the thermostat fan to AUTO. If that does not stop it, turn the furnace off at the power switch on or near the unit, or flip the furnace breaker in the electrical panel. That is a temporary measure. If the blower starts again as soon as you restore power, call for service.

Why does my furnace blower keep running after the burners shut off?

A short run after the burners stop is normal. The fan-off delay pushes remaining heat out of the exchanger and typically lasts one to three minutes. If the blower runs much longer than that, the limit switch may have tripped on high temperature, the relay may be stuck, or the thermostat fan is set to ON.

Can I bypass the limit switch to stop the blower?

Never bypass a limit switch. It is a safety device that prevents the heat exchanger from overheating and protects against carbon monoxide exposure. If the switch is tripping, the real problem is whatever is causing the furnace to overheat, usually restricted airflow.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service