Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Furnace error codes: reading and understanding the blinking LED

Most modern furnaces have a diagnostic LED on the control board visible through a small window in the blower door. The LED blinks in a repeating pattern: count the flashes, note the pause, and match the pattern to the chart printed on the inside of the door panel. Common codes point to ignition failure, flame-sensor faults, pressure-switch problems, or high-limit trips. The code tells a technician exactly where in the startup sequence the furnace failed, which saves diagnostic time. You can safely read the code without opening the furnace.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 7 sections
  1. 01Where to find the LED and how to read it
  2. 02Common error codes and what they point to
  3. 03Brand-specific notes
  4. 04Codes that need immediate attention
  5. 05What the code does not tell you
  6. 06Clearing and resetting codes
  7. 07Using error codes when talking to a technician

Where to find the LED and how to read it

The diagnostic LED sits on the main control board inside the blower compartment. On most furnaces you can see it through a small round or rectangular sight window in the lower access door without removing anything. Carrier advises looking through the window on the furnace door and matching the flash sequence to the code chart on the panel.

The LED blinks in a repeating loop. A typical pattern looks like this: a set of flashes, a pause of a few seconds, and then the same set repeats. Count the flashes in each set. Some boards use two-digit codes with a distinct pause between the first and second digit. The code chart on the inside of the blower door or on a sticker on the furnace cabinet shows what each pattern means.

A steady slow blink (heartbeat) usually means the board is powered and idle, with no call for heat and no fault. A rapid continuous blink often means the board is in an active heating call. A specific flash count repeated in a loop indicates a stored fault.

Common error codes and what they point to

Code numbers vary by manufacturer and model, so always refer to the chart on your furnace. The table below shows the most frequently encountered fault categories and the flash counts that typically correspond to them across major brands. These are representative; your furnace may differ.

Common furnace LED flash codes by fault category
Flash count (typical)Fault categoryWhat it usually meansHomeowner action
1 flashIgnition failure or system lockoutFurnace tried to light and failed after multiple attemptsCheck gas valve is open; note code and call for service
2 flashesPressure switch stuck closedPressure switch is reading closed before the inducer starts; possible wiring or switch faultNote code and call for service
3 flashesPressure switch open or failed to closeInducer cannot prove airflow; blocked vent, cracked hose, or switch faultCheck outdoor vent terminations for blockage; call for service if clear
4 flashesOpen limit switch (high-limit or auxiliary)Furnace overheated, typically from restricted airflowReplace clogged filter; open blocked registers; call if it persists
5 flashesFlame sensed without gas valve callBoard detects flame current when there should be none; possible valve leak or wiring shortCall for service immediately
6 flashesRollout switch openFlame escaping the burner area; serious safety conditionDo not reset; call for service immediately
7 flashesLow flame signalFlame sensor reading is below threshold; dirty sensor or weak flameNote code and call for service
Continuous rapid flashLine voltage polarity reversed or board faultElectrical wiring issue or a damaged boardCall for service; do not attempt wiring work

Brand-specific notes

Each manufacturer assigns its own meaning to each flash count. The codes overlap on some faults and diverge on others.

Lennox: Uses a red LED with a half-second on, half-second off rapid-flash pattern. The board stores the last ten error codes in memory, even through a power cycle. Pressing and releasing the diagnostic button shows the most recent code first. Code 3 on many Lennox boards means the burner failed to light or lost flame during a heat demand. Code 4 means low flame signal.

Goodman and Amana: Many Goodman boards use a single LED visible through the observation window. One flash typically means failure to establish flame. Three flashes indicate a pressure switch that did not close. Four flashes point to an open high-limit or auxiliary limit, often caused by a dirty filter or restricted ductwork. Seven flashes mean low flame-sense signal.

Carrier and Bryant: Carrier boards commonly use a two-digit flash code with a pause between digits. The code chart is printed on the blower door. Carrier recommends noting the sequence and reporting it to a technician rather than attempting internal diagnosis.

Trane and American Standard: Residential models use a similar single-LED blink scheme. Trane documentation notes that if multiple faults are stored, there is a two-second pause between each fault code, then a five-second pause before the sequence repeats.

Codes that need immediate attention

Most error codes indicate a part failure or airflow restriction that prevents normal operation but is not immediately dangerous. A few codes warrant more urgency:

  • Rollout switch open: This means flame escaped the burner assembly area. It is a serious condition that can indicate a cracked heat exchanger or blocked flue. Do not reset the rollout switch. Call for service.
  • Flame sensed without a call for heat: The board is reading flame current when the gas valve should be closed. This could mean a stuck-open gas valve. Call for service.
  • Repeated high-limit trips (4-flash pattern): One trip after a filter change may clear. Repeated trips mean the furnace is overheating consistently. Continued overheating stresses the heat exchanger. Replace the filter and open registers. If the code returns, call for service.

What the code does not tell you

An error code points to the stage in the sequence where the furnace stopped, not always to the specific failed part. A pressure-switch code might mean the switch itself failed, or it might mean the inducer motor is weak, the condensate trap is clogged, or the vent pipe is blocked. A flame-sense code might mean the sensor is dirty, or it might mean gas pressure is low or the burners are corroded.

This is why a code is a starting point for diagnosis, not a final answer. A technician uses the code to know where to begin testing. When you call for furnace repair, reporting the exact flash count and pattern speeds up the process.

Clearing and resetting codes

On most boards, cycling power at the furnace switch clears the active fault and lets the furnace try again. Some boards, like many Lennox models, store fault history that persists through power cycles and can be recalled with a button press.

One reset after a fault is reasonable. If the same code comes back on the next heating cycle, the fault is real and repeating. Do not keep resetting. Write down the code and call for service.

Some boards have a timed lockout, usually 60 minutes or three hours, after which the furnace will retry on its own. If you see the lockout code, you can either wait for the timer or cycle power once to clear it sooner.

Using error codes when talking to a technician

The most helpful information you can provide over the phone is the LED flash count, what the furnace was doing before it stopped (running normally, just started, first call of the season), and what you observed (inducer running, ignitor glowing, flame that lights then goes out). This lets the technician arrive with the right parts and a clear starting point.

Snap a photo of the code chart on the blower door if you can. Different models within the same brand sometimes use different code tables, and having the exact chart for your unit prevents misinterpretation.

For more on the heating system components that these codes reference, including the pressure switch, limit switch, inducer, and flame sensor, our heating hub and the furnace not turning on guide cover the full startup sequence.

Common questions

Where is the LED on my furnace?

It is on the main control board inside the blower compartment. Look for a small round or rectangular window in the lower access door. You do not need to open the door to see it.

Do all furnaces have diagnostic LED codes?

Most furnaces manufactured since the mid-1990s have a diagnostic LED. Very old furnaces with standing pilot lights and simple gas valves typically do not have a control board or LED.

What does a steady slow blinking LED mean?

A slow, regular heartbeat blink usually means the board is powered, functioning, and waiting. There is no fault stored and no active call for heat.

What does it mean when the LED is completely off?

No light means no power to the board. Check the furnace power switch, the circuit breaker, and whether the blower door is fully seated on its interlock switch.

Can I fix the problem the error code points to?

Homeowner-level fixes are limited to replacing the filter, opening blocked registers, clearing debris from outdoor vent pipes, and cycling power once. Anything beyond that involves parts inside the burner compartment or electrical components and needs a technician.

Why does my furnace show a different code each time?

Multiple stored faults can cycle on some boards, or the furnace may be failing at different stages on successive attempts. Report all codes you see. A technician can read the fault history on boards that store it.

Should I reset the rollout switch code myself?

No. A rollout switch trips when flame escapes the burner area, which is a serious safety condition. Do not reset it. Call for service so a technician can determine why flame rolled out of the burner assembly.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service