Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Winter thermostat settings: what to set, when to set back, and how to save

The U.S. Department of Energy recommends 68 degrees Fahrenheit when you are home and awake, with a setback of 7 to 10 degrees when sleeping or away for eight hours. That setback can save as much as 10 percent per year on heating and cooling. Keep the fan switch on AUTO so the blower only runs during heating cycles. A programmable or smart thermostat automates the schedule. ENERGY STAR certified smart thermostats save an average of about 8 percent on heating and cooling bills based on real-world field data verified by the EPA.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 7 sections
  1. 01The 68-degree baseline
  2. 02Setback schedules: sleep and away
  3. 03Fan setting: AUTO versus ON
  4. 04Programmable thermostats
  5. 05Smart thermostats and furnaces
  6. 06Setbacks and heat pumps: a different rule
  7. 07Local considerations for the Sacramento region

The 68-degree baseline

Both PG&E and the U.S. Department of Energy recommend 68 degrees Fahrenheit as a starting point for the heating season when you are home and awake. Trane's guidance agrees. The number is not arbitrary: it sits at the lower end of the comfort range while keeping furnace runtime moderate.

PG&E notes that three to five percent more energy is used for each degree you set the thermostat above 68. A household that bumps the setpoint from 68 to 72 in the name of comfort may use 12 to 20 percent more heating energy, depending on the house and the outdoor temperature.

Start at 68 and adjust by one degree at a time. Most people acclimate within a day or two. If you reach a point where you feel cold at 68, check the house for drafts, duct problems, or uneven heating before raising the setpoint.

Setback schedules: sleep and away

The Department of Energy estimates that turning the thermostat back 7 to 10 degrees from its normal setting for eight hours a day can save as much as 10 percent per year on heating and cooling. That eight-hour window lines up with sleeping hours, work hours, or both.

A practical schedule for a household that sleeps from 10 PM to 6 AM and works from 8 AM to 5 PM might look like this:

Sample weekday thermostat schedule
Time blockSettingWhy
6:00 AM to 8:00 AM68 degrees FahrenheitRecovery before the household is active; start the warm-up 30 minutes before waking if the thermostat supports it
8:00 AM to 5:00 PM58 to 60 degrees FahrenheitSetback while the house is empty; keeps pipes safe and prevents the furnace from a deep recovery
5:00 PM to 10:00 PM68 degrees FahrenheitOccupied hours; the furnace recovers and holds the setpoint
10:00 PM to 6:00 AM60 to 62 degrees FahrenheitSleep setback; a layer of bedding compensates for the lower air temperature

Fan setting: AUTO versus ON

The thermostat fan switch controls when the blower runs. In AUTO the blower turns on only when the furnace is actively heating and stays on briefly after the burners shut off to clear remaining heat from the exchanger. In ON the blower runs continuously whether the burners are firing or not.

For most heating situations, AUTO is the right setting. ON pushes unheated air through the ducts between cycles, which can make rooms feel drafty and prompt someone to raise the setpoint. It also adds electricity cost for the blower motor. Trane identifies the fan switch set to ON as the most common reason a homeowner thinks the furnace blower will not shut off.

There are edge cases where ON or a circulate mode makes sense: distributing air in a house with poor duct layout, reducing stratification in tall rooms, or running air through a whole-house filtration system continuously. But those are specific situations, not the default. If you run the fan continuously, expect the blower to use more electricity and plan on more frequent filter changes.

Programmable thermostats

A basic programmable thermostat lets you set different temperatures for wake, leave, return, and sleep periods on weekdays and weekends. The hardware has been around for decades and is inexpensive. The catch is that the savings only happen if someone programs the schedule and then leaves it alone. Overriding the program regularly erases the setback benefit.

If the household sticks to a consistent routine, a 7-day programmable thermostat captures most of the available savings. For households with irregular schedules, a smart thermostat may be a better fit.

Smart thermostats and furnaces

ENERGY STAR certified smart thermostats save an average of about 8 percent on heating and cooling bills, based on field data from homes across the country verified by EPA-recognized certification bodies. The specification requires a minimum runtime reduction of 8 percent for heating and 10 percent for cooling.

Smart thermostats earn those savings through occupancy sensing, geofencing, and learning algorithms that adjust the schedule without manual programming. Some models pre-heat the house so it reaches the setpoint by the time you arrive, rather than starting the recovery when you walk in the door.

Compatibility matters. Most smart thermostats work with standard 24-volt furnace systems, but some older furnaces lack a C (common) wire, which smart thermostats need for power. Check the thermostat manufacturer's compatibility tool before buying. If you have a heat pump or a dual-fuel system, verify that the thermostat supports your equipment's staging and auxiliary heat.

Setbacks and heat pumps: a different rule

The 7-to-10-degree setback works well with gas furnaces. Heat pumps are a different story. A deep setback on a conventional heat pump can trigger expensive auxiliary electric-resistance heat during recovery. Carrier recommends that heat pump owners follow their specific system and thermostat recommendations rather than applying the standard setback rule.

If you have a dual-fuel system (heat pump with a gas furnace backup), the thermostat controls which system runs based on outdoor temperature. A smart thermostat designed for dual fuel manages the switchover and setback together. Our heat pump guide covers dual-fuel thermostat considerations.

Local considerations for the Sacramento region

On the Sacramento Valley floor, heating season is short. Most winter days have lows in the 35-to-45-degree range, which means the furnace does moderate work. A setback schedule pays off here because the mild daytime temperatures let the house hold heat reasonably well during the away period.

In the foothills, nighttime lows can drop into the 20s, and the furnace runs longer. A shallower sleep setback of 5 to 7 degrees may be more practical at elevation because the recovery period in the morning takes longer. Homes on propane benefit even more from setbacks because propane costs more per unit of heat than natural gas.

SMUD customers in Sacramento County can take advantage of their time-of-day rate structure. SMUD's peak hours are 5 to 8 PM, so pre-heating the house before 5 PM and coasting through the evening can reduce the electricity portion of heating costs for heat pump owners. PG&E has similar time-of-use structures. Checking your utility rate plan and aligning the thermostat schedule to it adds another layer of savings. Visit our heating hub for seasonal maintenance steps that pair with thermostat settings.

Common questions

What is the best thermostat setting for winter?

The U.S. Department of Energy and PG&E both recommend 68 degrees Fahrenheit when you are home and awake. Lower it 7 to 10 degrees when sleeping or away for eight hours to save as much as 10 percent per year on heating and cooling.

Should I set my thermostat fan to AUTO or ON in winter?

AUTO for most situations. In AUTO the blower runs only during heating cycles and a short cool-down after. ON keeps the blower running all the time, pushing unheated air between cycles and adding electricity cost.

How much can a smart thermostat save on heating?

ENERGY STAR certified smart thermostats save an average of about 8 percent on heating and cooling bills, based on EPA-verified field data. Actual savings depend on your previous thermostat habits, climate, and equipment.

Is it bad to turn the heat way down at night?

No. A setback of 7 to 10 degrees while you sleep is one of the most effective ways to save on heating. The furnace runs a longer recovery cycle in the morning, but the total gas used is still less than holding a higher temperature all night.

Does turning the thermostat up higher heat the house faster?

No. A standard furnace runs at the same output regardless of the setpoint. Setting it to 80 does not make it heat faster than setting it to 68. It just makes the furnace run until the house reaches 80, wasting energy and overshooting your comfort range.

What temperature should I set when I go on vacation in winter?

Set it no lower than 55 degrees Fahrenheit to prevent pipes from freezing. SMUD recommends 55 degrees when no one is home. If the house has pipes in exterior walls or an unheated garage, consider a slightly higher setpoint or insulating the pipes.

Do I need a C wire for a smart thermostat?

Most smart thermostats need a C (common) wire for steady power. Many newer furnaces already have one connected. If yours does not, an adapter kit can add one without running new wire. Check the thermostat manufacturer's compatibility tool before purchasing.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service