On this page · 6 sections
Start at the thermostat
Before anything else, look at three settings. The mode should be HEAT, not COOL or OFF. The setpoint should be a few degrees above the current room temperature, so the furnace actually has a reason to fire. The fan should be set to AUTO, not ON.
Fan ON is the most common cause of a 'cold air' call. With the fan set to ON, the blower runs all the time, including between heating cycles when the burners are off, so for much of the hour the vents push room-temperature air that feels cool on your hand. Switch it to AUTO, and the blower runs only while the furnace is heating. Battery-powered thermostats with a weak or blank display are worth a fresh set of batteries before you call anyone.
Cool air that's actually normal
Some cool air is part of a healthy cycle:
- Startup. A gas furnace lights the burners first and waits before starting the blower, so the heat exchanger warms up. If the ducts run through a cold attic, as they do in many Sacramento-area homes, the first air out of the vents is the cold air that sat in those ducts. It should turn warm within a minute or two.
- Shutdown. After the burners shut off, the blower runs on for a short time to pull leftover heat out of the heat exchanger. That air cools as the cycle ends.
- Heat pump air. A heat pump delivers air that's warm but cooler than a gas furnace's supply air, so it can feel lukewarm on your hand even though the house is heating normally. See the heat pump section below.
When the burners won't light or stay lit
If the blower runs and the air never warms up, the furnace is probably going through its ignition sequence and failing. Modern furnaces retry a set number of times and then lock out, sometimes leaving the blower running to cool things down. The LED on the control board, usually visible through a small window in the blower door, will blink a code that matches a chart on the door.
- Flame sensor. The burners light, then go out within seconds because the sensor can't confirm a flame. A dirty sensor is common, and cleaning it is a technician job inside the burner compartment.
- Hot-surface ignitor. If you never see a glow or hear the burners light, the ignitor may have cracked or burned out. These are fragile and wear out with age.
- Standing pilot (older furnaces). If you have an older furnace with a pilot light that has gone out, relight it only by following the instructions printed on the furnace label. If it won't stay lit, the thermocouple or pilot assembly likely needs service.
- Gas supply. Check whether other gas appliances, such as the range or water heater, are working, and make sure the shutoff valve on the furnace's gas line hasn't been turned off. Foothill homes on propane should check the tank level.
- Blocked venting or inducer problems. If the inducer runs but the pressure switch never confirms draft, the furnace won't light. On condensing furnaces, check the outdoor PVC pipes for obstructions.
Overheating and condensate shutdowns
A clogged filter, or a lot of closed or blocked registers, cuts airflow across the heat exchanger. The furnace overheats, the high-limit switch shuts off the burners, and the blower keeps running to cool the heat exchanger. You feel cool air from a furnace that was hot a few minutes ago. Replace the filter and open the registers. If it keeps happening, the airflow problem is somewhere else and needs a technician. Our filter guide explains the mechanism.
On 90%+ condensing furnaces, the burners produce water that drains through a trap and a condensate line, sometimes to a small pump. If the trap or line clogs, or the pump fails, a safety switch shuts the burners down to prevent water damage, while the blower may still run. Signs include water around the furnace or a condensate pump that hums but doesn't empty. Check the pump's outlet tubing for kinks. Clearing the trap and the pressure-switch tubing is technician work.
If you have a heat pump: defrost mode
Many Sacramento-region homes heat with a heat pump, or with a heat pump paired with a gas furnace. On cold, damp mornings, frost builds up on the outdoor coil, and the system runs a defrost cycle to melt it. Trane describes defrost as a normal process that can send a cloud of steam up from the outdoor unit, with its demand-defrost cycles usually lasting a few minutes.
During defrost, many systems turn on electric backup heat so you barely notice. Homes without backup heat may feel cooler air from the vents for those few minutes, which is also normal. It isn't normal for the outdoor coil to stay iced over after defrost, for defrost to repeat constantly in mild weather, or for the air to stay cool for long periods. Those need a service call. Our heat pump cold-weather guide covers how heat pumps perform in our winters.
Safety: gas smell, carbon monoxide, and when to stop
If you smell gas, don't troubleshoot. PG&E's guidance is to leave the area, alert everyone in the household, avoid matches, flashlights and other possible ignition sources, call 911, and then call PG&E at 1-800-743-5000.
If a carbon monoxide alarm sounds, or people in the home have headache, dizziness, weakness, nausea, vomiting, sleepiness or confusion while the furnace runs, the U.S. Consumer Product Safety Commission says to get outside to fresh air and call 911. CPSC recommends CO alarms on every level of the home and outside sleeping areas.
Never bypass a limit switch, rollout switch or pressure switch to get the heat back on. Those controls shut the burners off because something is wrong. After one reset, if the furnace locks out again, write down the error code and call for service.
Common questions
Why does my furnace blow cold air before it gets warm?
A gas furnace lights its burners before the blower starts, but air left in the ducts, especially ducts in a cold attic, comes out first. That should turn warm within a minute or two. If it never warms up, the burners aren't lighting or staying lit.
Should my thermostat fan be on ON or AUTO in winter?
AUTO for most homes. With the fan on ON, the blower runs between heating cycles and pushes room-temperature air that feels cold. AUTO runs the blower only while the furnace is heating.
Can a dirty filter make a furnace blow cold air?
Yes. A clogged filter starves the heat exchanger of airflow, the furnace overheats, and the high-limit switch shuts off the burners while the blower keeps running. Replace the filter first. If the problem returns, have the airflow checked.
My heat pump is blowing cool air and steaming outside. Is it broken?
Probably not. That's usually a defrost cycle melting frost off the outdoor coil, which typically lasts a few minutes before heating resumes. If the coil stays iced or the air stays cool for a long time, call for service.
Is it safe to keep resetting my furnace?
One reset to clear a lockout is reasonable. If the furnace locks out again, a safety control has shut it down for a reason, so stop resetting it, write down the blinking error code, and call a technician.
Sources
- U.S. Consumer Product Safety Commission — Carbon Monoxide Information Center (checked October 26, 2026)
- Pacific Gas and Electric Company — Keep yourself safe from a gas leak (checked October 26, 2026)
- Trane — What Is a Heat Pump Defrost Cycle? (checked October 26, 2026)
Program amounts and rules change. Confirm current terms with the source before you rely on them.
Reviewed and published by Statewide HVAC

Vasiliy Bardadin
Owner & Lead Technician
Statewide HVAC is owner-operated and Roseville-based.
Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us
