Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Furnace parts and the repairs they need

Every gas furnace relies on a sequence of parts that fire in order: the draft inducer clears the vent path, the pressure switch confirms airflow, the ignitor lights the burners, the flame sensor proves the flame, and the blower motor pushes heated air through the ducts. The high-limit switch and rollout switches watch for overheating. When one part fails, the furnace usually shuts down or short cycles and throws an error code. Most of these parts are technician-only repairs because they involve gas, line voltage, or the combustion chamber.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 9 sections
  1. 01How a furnace heating cycle works
  2. 02Ignitor
  3. 03Flame sensor
  4. 04Draft inducer motor
  5. 05Pressure switch, limit switches, and gas valve
  6. 06Blower motor and control board
  7. 07Heat exchanger
  8. 08Parts at a glance
  9. 09What you can check before calling

How a furnace heating cycle works

Before talking about parts, it helps to understand the sequence they follow. A heating call starts at the thermostat. The control board receives the signal and starts the draft inducer motor, which pulls air through the heat exchanger and up the flue or PVC vent. Once the pressure switch confirms that airflow, the ignitor heats up (or, on older units, the pilot lights the burners). The gas valve opens. Burners light. The flame sensor verifies the flame within a few seconds.

After the heat exchanger warms up, the high-limit switch tells the blower motor to start pushing heated air through the ducts. When the thermostat is satisfied, the gas valve closes, burners shut off, and the blower keeps running for a short cool-down before stopping. Every part in that chain has a specific job, and a failure at any point stops the cycle. The error code on the control board usually tells a technician exactly where the sequence broke.

Ignitor

The ignitor is the part that lights the burners. Most furnaces made in the last 25 years use a hot-surface ignitor, a small silicon carbide or silicon nitride element that glows to around 1,800 degrees Fahrenheit when energized. Older furnaces may use a spark ignitor or a standing pilot light.

Hot-surface ignitors fail because they are fragile and exposed to extreme heat every cycle. Over time the element cracks or loses enough resistance to stop reaching ignition temperature. The symptom is a furnace that tries to start but never lights, or lights intermittently. You may see a faint glow through the sight glass that doesn't get bright enough. According to Carrier, the ignitor is one of the parts that typically fails earliest in a furnace's life.

Replacement is a technician job. It involves opening the burner compartment, disconnecting the old ignitor, and installing one matched to the furnace model. The part itself is inexpensive relative to most furnace components, and the repair is usually quick. If your furnace won't ignite, a failed ignitor is one of the first things a tech will check.

Flame sensor

The flame sensor is a thin metallic rod mounted in the burner assembly. It uses a principle called flame rectification: a small electrical current passes through the flame to the sensor rod, and the control board reads that current to confirm the burners are actually lit. If the board doesn't see the expected signal within a few seconds of the gas valve opening, it shuts everything down. That's by design. Running gas without a confirmed flame would fill the heat exchanger with unburned fuel.

Carrier notes that carbon buildup or oxidation on the sensor rod is the most common cause of failure. A thin layer of residue insulates the rod just enough to weaken the signal below the board's threshold. The furnace lights, runs for two to five seconds, and shuts off. After a few retries it locks out. This pattern is distinct enough that most technicians diagnose it before they open the panel.

A cracked porcelain insulator, a bent rod, or age can also cause failure. Cleaning or replacing the flame sensor is straightforward for a technician, but it is inside the burner compartment. Carrier states explicitly that homeowners should not bypass, disconnect, or defeat the flame sensor because it is a safety component.

Draft inducer motor

The draft inducer is a small motor-driven fan mounted at the top of the heat exchanger or near the exhaust flue. It starts before the burners light and runs through the entire heating cycle. Its job is to pull combustion gases through the heat exchanger and out the vent, creating the negative pressure that the pressure switch monitors.

Inducer motors fail from bearing wear, winding shorts, or debris buildup. A failing inducer often announces itself with a loud humming, buzzing, or grinding noise at startup. If it can't spin up, the pressure switch never closes and the ignition sequence stops. If it runs but doesn't generate enough draft, you get intermittent pressure-switch faults and lockouts. Our furnace noises guide covers the sounds each part makes.

Replacing the inducer motor means pulling the old assembly and installing a replacement matched to the furnace. The motor is wired to the control board and sealed to the heat exchanger housing, so this is strictly technician work.

Pressure switch, limit switches, and gas valve

The pressure switch is a small diaphragm-operated switch connected to the inducer housing by a rubber hose. It confirms that the inducer is pulling enough draft before the board allows ignition. A cracked diaphragm, a plugged hose, or a weak inducer all cause the pressure switch to stay open and block the ignition sequence.

The high-limit switch monitors the temperature inside the furnace cabinet. Carrier describes it as a safety device that shuts the burners off if internal temperatures climb too high, typically above around 200 degrees Fahrenheit. A clogged filter, blocked returns, or a failing blower motor can all cause the limit to trip. Rollout switches sit near the burner tray and trip if flames roll out of the combustion chamber, a sign of a cracked heat exchanger or blocked flue. None of these switches should ever be bypassed. They exist to stop dangerous conditions, and a tripped safety switch means the underlying cause needs to be found.

The gas valve is the part that controls fuel flow to the burners. Carrier describes it as a gatekeeper that opens only when the thermostat calls for heat and the safety chain is satisfied. Gas valves cannot be repaired. A failed valve is replaced entirely, and the work involves handling gas connections, so it is licensed-technician work. If you smell gas near the furnace, leave the house and call your gas utility or 911 from outside.

Blower motor and control board

The blower motor is the largest motor in the furnace. It drives the fan that pushes heated air through the duct system and pulls return air back. Blower motors come in two types: PSC (permanent split capacitor) motors that run at one or a few fixed speeds, and ECM (electronically commutated motor) motors that ramp up and down to match demand. ECM motors are quieter and more efficient, and ENERGY STAR certified furnaces require them.

Blower motors fail from overheating, bearing wear, or capacitor failure (on PSC motors). A failing blower may run slowly, make a squealing or grinding sound, or stop altogether. If the blower doesn't run, heated air stays in the cabinet, the limit switch trips, and the furnace shuts down. A blower that won't shut off points to a relay or board issue rather than the motor itself.

The control board is the brain. It sequences every step of the heating cycle, reads safety switches, stores error codes, and manages timing delays. Board failures can produce erratic behavior: random lockouts, incorrect fan speeds, or error codes that don't match the symptom. Diagnosing a board fault takes a technician with a meter and the wiring diagram for your specific furnace.

Heat exchanger

The heat exchanger is the set of metal chambers or tubes where combustion happens. Burner flame heats the inside surface, and the blower pushes house air over the outside surface. The wall of the exchanger is the barrier between combustion gases and your breathable air. A crack or hole in that wall can allow carbon monoxide into the airstream.

Heat exchangers fail from thermal stress over years of expansion and contraction. Oversized furnaces that short cycle accelerate this because each on-off cycle adds a thermal stress event. Lennox notes that a cracked heat exchanger is rarely repaired; replacement of the exchanger or the entire furnace is the standard recommendation because of the carbon monoxide risk. Our cracked heat exchanger guide covers the details.

A technician finds cracks through visual inspection, a combustion analyzer, or a camera scope. The U.S. Consumer Product Safety Commission recommends annual professional inspection of all fuel-burning heating equipment, and checking the heat exchanger is a central part of that inspection.

Parts at a glance

The table below summarizes what each part does, the typical symptom when it fails, and whether the repair is something a homeowner can handle or requires a technician.

Common furnace parts: function, failure symptoms, and who handles the repair
PartWhat it doesTypical failure symptomWho handles it
Hot-surface ignitorHeats to light the burnersFurnace tries to start but burners never lightTechnician
Flame sensorConfirms burners are litBurners light then shut off within seconds; lockout after retriesTechnician
Draft inducer motorPulls combustion air through the heat exchanger and ventLoud hum or buzz at startup; furnace won't proceed past inducer stageTechnician
Pressure switchVerifies the inducer is creating enough draftIgnition sequence stops before burners light; pressure-switch error codeTechnician
High-limit switchShuts burners off if cabinet temperature is too highFurnace runs briefly then shuts off; blower keeps runningTechnician diagnoses; homeowner checks filter first
Rollout switchTrips if flame escapes the burner areaFurnace locks out; manual reset button on switchTechnician (indicates a serious problem)
Gas valveControls fuel flow to the burnersNo ignition despite working ignitor; gas smell if valve leaksLicensed technician only
Blower motorPushes heated air through the ductsWeak airflow, squealing, or no air movement; limit switch tripsTechnician
Control boardSequences the entire heating cycleErratic behavior, random lockouts, mismatched error codesTechnician
Heat exchangerTransfers combustion heat to house air while containing exhaust gasesCO alarm, soot near burners, visible cracks on inspectionTechnician; usually means replacement

What you can check before calling

None of the parts above are homeowner repairs. They all involve the burner compartment, gas, or line voltage. But before calling for service, there are a few things worth checking because they often mimic a part failure. Our heating hub covers the full range of furnace and heat pump topics if you want to dig deeper.

  • The filter. A plugged filter restricts airflow and trips the high-limit switch, which looks like a limit-switch or blower-motor problem. Pull the filter and replace it if it's dirty. Our filter and airflow guide explains the connection.
  • The thermostat. Make sure it's set to heat, the setpoint is above room temperature, and the batteries aren't dead.
  • The power switch. Furnaces have a wall switch that looks like a light switch. Make sure it's on. Check the breaker too.
  • The error code. Look through the small sight window on the blower door for a blinking LED. Count the blinks and match them to the chart on the door. That code is the single most useful thing you can tell a technician.
  • Registers and returns. Open supply registers and clear anything blocking return grilles. Restricted airflow is behind a large share of limit-switch trips.

Common questions

What is the most common furnace repair?

Ignitor replacement and flame sensor cleaning are the two most frequent furnace repairs. Both are relatively quick for a technician. A clogged filter causing a limit-switch trip is also extremely common, and that one you can fix yourself by replacing the filter.

Can I clean my own flame sensor?

The flame sensor is inside the burner compartment, which means working near gas lines and the combustion area. Carrier recommends having internal furnace components maintained by a trained HVAC professional. Leave the flame sensor to a technician.

How do I know which part failed in my furnace?

Most modern furnaces have an LED on the control board visible through a small window in the blower door. The LED blinks a code that points to the failed part or the step in the sequence where the cycle stopped. Match the blink pattern to the chart on the furnace door and relay that to your technician.

Is it worth replacing a heat exchanger, or should I replace the whole furnace?

A cracked heat exchanger on a furnace that's nearing the end of its expected 15-to-20-year life usually makes full replacement the better path. The exchanger repair cost is often more than half the cost of a new furnace, and the rest of the old system is aging alongside it.

Should I ever bypass a safety switch to keep the furnace running?

No. The high-limit switch, rollout switches, and pressure switch are there to stop dangerous conditions like overheating, flame rollout, and blocked venting. Bypassing one removes the protection and can lead to a cracked heat exchanger or carbon monoxide in the house. If a safety switch keeps tripping, the cause needs to be diagnosed.

What furnace parts does a tune-up cover?

A professional tune-up typically includes cleaning the flame sensor, checking the ignitor, inspecting the heat exchanger, testing safety switches, measuring gas pressure, checking the blower motor and its electrical draw, and verifying that the inducer and venting are clear. The CPSC recommends annual professional inspection of all fuel-burning heating equipment.

Why does my furnace keep locking out?

Repeated lockouts mean a safety control is detecting a problem on every attempt. Common causes are a dirty flame sensor, a failing inducer motor, a cracked pressure-switch hose, or restricted airflow tripping the high limit. The control board's error code narrows the cause. Stop resetting the furnace after one retry and call for service.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service