Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

Furnace pilot light out: what to check and when to call

On an older standing-pilot furnace, the small flame near the burners stays lit continuously. If it goes out, the thermocouple closes the gas valve automatically to prevent gas buildup. You can try relighting the pilot following the manufacturer's instructions posted on or inside the unit. Turn the gas control knob to Off, wait five minutes for any gas to clear, switch to Pilot, press and hold the knob while using a long-reach lighter, and hold for about 30 seconds to let the thermocouple heat up. If the pilot will not stay lit after two attempts, the thermocouple or gas valve likely needs replacement by a technician.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 8 sections
  1. 01How a standing pilot light works
  2. 02Why pilot lights go out
  3. 03How to relight the pilot safely
  4. 04What the flame color tells you
  5. 05The thermocouple in detail
  6. 06Standing pilot versus electronic ignition
  7. 07Sacramento-region notes
  8. 08Safety reminders

How a standing pilot light works

Older gas furnaces, generally those manufactured before the mid-1990s, use a standing pilot light. A small flame burns continuously near the main burner assembly. When the thermostat calls for heat, the gas valve opens and the pilot flame ignites the main burners.

A safety device called the thermocouple sits with its tip in the pilot flame. Carrier describes the thermocouple as a sensor that generates a small electrical current when heated by the pilot flame, signaling the gas valve to stay open. If the pilot goes out, the thermocouple cools, the current stops, and the gas valve closes automatically. This prevents unburned gas from filling the burner compartment and the living space.

Newer furnaces use electronic ignition instead, either a hot-surface ignitor or a spark igniter, and do not have a standing pilot. If your furnace was manufactured in the last 20 to 25 years, it almost certainly uses electronic ignition. See our furnace ignition guide if you have a newer system.

Why pilot lights go out

A pilot light that goes out once and relights easily was probably hit by a draft. A pilot that goes out repeatedly has a part that needs attention. The table below covers the common causes.

Common reasons a furnace pilot light goes out
CauseWhat you'd noticeHomeowner fix?Typical repair
Drafts near the furnacePilot blows out during windy weather or when a nearby door opensPartly: check for obvious air paths near the furnaceSeal drafts; if the combustion air supply is inadequate the install may need correction
Failing thermocouplePilot lights when you hold the knob, goes out within seconds of releasingNoTechnician replaces the thermocouple
Dirty pilot orificeWeak, small, or wavering pilot flame; may not reach the thermocouple tipNoTechnician cleans or replaces the pilot assembly
Faulty gas valvePilot will not light at all, or main burners do not fire even with a steady pilotNoTechnician tests and replaces the gas valve
Low gas pressurePilot is small and yellow; other gas appliances also perform poorlyCheck if other gas appliances work normallyContact gas utility if pressure is low system-wide
Thermocouple misalignmentPilot lights but thermocouple tip is not in the flame; pilot will not holdNoTechnician repositions or replaces the thermocouple

How to relight the pilot safely

Follow the lighting instructions printed on the furnace itself. Different manufacturers use slightly different valve designs, so the posted instructions for your specific unit take priority over any general guide. Trane recommends waiting at least five minutes after turning the gas off before attempting to relight, to allow any accumulated gas to dissipate. The general steps are:

  • Turn the gas control knob to the Off position and wait a full five minutes. If you smell gas at any point, do not proceed. Leave the house and call your gas utility or 911 from outside.
  • Turn the knob to the Pilot position and press it in. This manually opens a small gas passage to the pilot.
  • While holding the knob in, use a long-reach lighter or the built-in piezo button to light the pilot.
  • Keep holding the knob for about 30 seconds after the pilot lights. This gives the thermocouple time to heat up and generate enough current to hold the gas valve open on its own.
  • Release the knob slowly. If the pilot stays lit, turn the knob to the On position and set the thermostat to call for heat.
  • If the pilot goes out when you release the knob, wait five minutes and try once more. If it goes out a second time, stop. Repeated attempts without a functioning thermocouple will not fix the problem.

What the flame color tells you

A healthy pilot flame is mostly blue with a small yellow tip. It should be steady and wrap around the thermocouple tip. Carrier notes that a yellow or orange pilot flame points to incomplete combustion, which can mean a dirty orifice, inadequate combustion air, or an air-mixture adjustment that is off.

A yellow, flickering, or lazy pilot flame may not heat the thermocouple enough to keep the gas valve open. It also means the pilot is not burning cleanly. If your pilot flame is yellow, do not keep using the furnace. Call for service.

The thermocouple in detail

The thermocouple is a bimetallic sensor: two different metals joined at the tip. When the pilot flame heats that junction, the difference in the metals creates a small electrical voltage, typically in the millivolt range. That voltage feeds back to an electromagnet in the gas valve, holding the valve open.

When the thermocouple fails, it usually fails gradually. The voltage drops as the junction corrodes or cracks, and the gas valve starts dropping out intermittently before it stops holding altogether. A furnace that holds the pilot for a few minutes and then drops it is a classic thermocouple on its way out.

Thermocouple replacement is a straightforward repair for a technician. The part is inexpensive, and the job takes less than an hour in most furnaces. If the thermocouple has been replaced recently and the pilot still will not hold, the gas valve itself is the next suspect.

Standing pilot versus electronic ignition

Standing pilot furnaces are less efficient than modern electronic-ignition models because the pilot burns gas around the clock whether the furnace is heating or not. The U.S. Department of Energy notes that high-efficiency condensing furnaces reach 90 to 98 percent AFUE, while many older pilot-lit furnaces operate in the range of 56 to 72 percent AFUE.

If your pilot-lit furnace is nearing the end of its service life, a replacement with a modern unit will eliminate the pilot light entirely and deliver substantially better efficiency. Our furnace guide covers the decision between repair and replacement, and the heating hub has more on system options.

Sacramento-region notes

Standing-pilot furnaces still turn up in older Sacramento Valley homes, particularly in neighborhoods built before the 1990s. Many of these are floor furnaces or wall furnaces, which use a standing pilot and a thermocouple and sit at floor level in a hallway or central room rather than in an attic or garage.

In the foothills, propane-fueled standing-pilot furnaces are more common where homes are off the natural gas main. The same thermocouple and relighting principles apply, but propane has a higher vapor density than natural gas, meaning it settles rather than rising. That makes the five-minute wait after turning the gas off especially important.

Safety reminders

If you smell gas at any point, whether the pilot is out or not, leave the house immediately without operating light switches or appliances. Call your gas utility or 911 from outside.

The U.S. Consumer Product Safety Commission recommends CO alarms on every level of the home and outside sleeping areas. An older furnace with a failing pilot or thermocouple can produce incomplete combustion. If a CO alarm sounds or anyone in the house feels headache, dizziness, or nausea, get outside and call 911.

A pilot that repeatedly goes out is telling you something is wrong. Relighting it over and over without fixing the underlying cause is not a solution. Have the furnace inspected by a licensed technician. For regular upkeep steps, see our furnace tune-up checklist.

Common questions

How do I know if my furnace has a pilot light?

Look for a small viewing window near the bottom of the furnace. If you see a small continuous flame, your furnace uses a standing pilot. Most furnaces built after the mid-1990s use electronic ignition instead and have no standing pilot.

Why does the pilot go out as soon as I release the knob?

The thermocouple is not generating enough voltage to hold the gas valve open. Either the thermocouple has failed, the pilot flame is too weak to heat it, or the thermocouple tip is not positioned in the flame. A technician replaces or repositions the thermocouple.

Is it dangerous if the pilot light goes out?

The thermocouple is designed to shut off the gas automatically when the pilot goes out, so a working thermocouple prevents gas from accumulating. The risk comes if you smell gas, which means gas may be escaping. Leave the house and call your gas utility or 911.

Can I replace the thermocouple myself?

The thermocouple is inside the burner compartment and connects to the gas valve. Accessing and replacing it involves working near gas piping and the pilot assembly. This is a repair for a licensed technician.

Should I replace a standing-pilot furnace?

If the furnace is otherwise working and the repair is a thermocouple, the repair is inexpensive and reasonable. If the furnace is 20 or more years old and needing frequent repairs, replacing it with a modern electronic-ignition furnace improves efficiency and eliminates the pilot. Our furnace guide covers the repair-versus-replace decision.

What does a yellow pilot flame mean?

A yellow or orange pilot flame indicates incomplete combustion, often caused by a dirty pilot orifice or insufficient combustion air. It may not heat the thermocouple enough to hold, and it means the pilot is not burning cleanly. Call for service rather than continuing to use the furnace.

Do modern furnaces have pilot lights?

Most modern furnaces use electronic ignition, either a hot-surface ignitor or an intermittent pilot that lights only when needed. They do not maintain a continuous standing pilot flame.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service