Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 12-minute read · Last reviewed November 2026

Converting from a gas furnace to a heat pump in the Sacramento region

A furnace-to-heat-pump conversion replaces the outdoor AC with a heat pump, swaps or adapts the indoor equipment, and usually adds or upsizes a 240-volt circuit. You decide whether to remove gas heating entirely or keep the furnace as backup in a dual-fuel setup, and whether other gas appliances stay. The job needs a mechanical permit and field verification by a certified rater. Which incentives and utility steps apply depends on whether your electric bill comes from SMUD, Roseville Electric, or PG&E.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 13 sections
  1. 01What this guide covers, and what it leaves to others
  2. 02What changes in the house
  3. 03Full electrification or dual fuel
  4. 04The gas line: cap it, keep it, or remove the service
  5. 05The duct check before anything is ordered
  6. 06How the path differs by electric utility
  7. 07SMUD territory: a conversion built around the rebate rules
  8. 08Roseville Electric: no utility heat pump rebate listed
  9. 09PG&E areas: Placer foothills, Rocklin, Davis and Yolo
  10. 10State and federal incentives in 2026
  11. 11Permits and HERS (now ECC) field verification
  12. 12A realistic sequence, start to finish
  13. 13Questions to ask any contractor about a conversion

What this guide covers, and what it leaves to others

If you've already decided a heat pump is worth considering, the next question is practical: what actually happens to the house when a gas furnace comes out and a heat pump goes in? That's the subject here. Whether a heat pump beats a furnace for your home is a separate decision, covered in our heat pump vs. furnace comparison, and the basics of how heat pumps work are in the heat pump guide.

We also don't repeat rebate amounts or price ranges on this page. Those change, and they live in guides that are kept current: the SMUD heat pump rebate guide, the Roseville Electric rebate status page, and the Sacramento heat pump cost guide. This page links to them at the points where they matter.

What changes in the house

Most Sacramento-region homes with a gas furnace also have a split central AC: a condenser outside, an evaporator coil sitting on top of (or under) the furnace inside, and a refrigerant line set connecting them. A conversion touches every one of those pieces, plus a few that homeowners don't expect.

  • Outdoor unit. The AC condenser is replaced with a heat pump outdoor unit. It looks similar, but it contains a reversing valve and defrost controls so it can heat as well as cool. It usually goes on the existing pad, though clearance, drainage in heating mode, and noise near bedrooms are worth a second look because it now runs in winter too.
  • Indoor coil or air handler. In a full electric conversion, the furnace comes out and an electric air handler takes its place, with a matched indoor coil and, in many installs, electric backup heat strips. In a dual-fuel conversion, the furnace stays and a heat-pump-rated coil sits on it. Either way, the indoor coil should be matched to the new outdoor unit, not reused from the old AC.
  • Refrigerant line set. Whether the existing copper lines can be reused depends on their size, condition, and the refrigerant the new system uses. Ask the contractor to say which it is and why.
  • Electrical circuit and panel capacity. A gas furnace runs on a small 120-volt circuit. An electric air handler with backup heat strips needs its own 240-volt circuit, and that added load is where panel questions start. Our panel requirements guide explains the load calculation and when an upgrade is actually needed.
  • Gas line. The furnace's gas branch is capped at the appliance location. Whether the gas service stays depends on what else in the house burns gas, covered below.
  • Ducts. The existing ducts get reconnected to the new indoor unit, and they need to be checked before anyone assumes they're fine. More on that below.
  • Thermostat. A heat pump needs a thermostat that can control it, including the backup heat stage. A dual-fuel system needs controls that decide when to switch from the heat pump to the furnace. An old furnace-and-AC thermostat often isn't compatible.

Full electrification or dual fuel

This is the biggest choice in a conversion, and it shapes the electrical work, the gas work, and which incentives might apply.

Full electrification means the heat pump is the only heating system. The furnace is removed, an electric air handler goes in, and backup heat (if any) is electric resistance. It uses only one fuel for heating and cooling, and if every other gas appliance is also electric, the home can drop gas service entirely. The tradeoff is electrical load: backup heat strips are what most often push an older panel toward an upgrade.

Dual fuel pairs the heat pump with the existing or a new gas furnace. The heat pump handles most heating hours and the furnace takes over below a set outdoor temperature. It can avoid large heat strips and the panel upgrade that sometimes comes with them, and it keeps gas heat on the coldest mornings, which some foothill homeowners prefer. The tradeoff is keeping two heating systems and the gas service that feeds the furnace. Our dual-fuel crossover guide explains how the switch point is chosen.

Neither choice is required by code for an existing home. The 2025 Title 24 heat pump baseline applies to new construction, and our guide to California's gas furnace rules explains what the state does and doesn't require when you replace equipment.

Full electrification vs. dual fuel: what each changes
ItemFull electrificationDual fuel
Gas furnaceRemovedKept (or replaced) as backup heat
Indoor unitElectric air handler with matched coilHeat-pump-rated coil on the furnace
Backup heatElectric heat strips, if anyGas furnace below the switch point
Electrical loadHigher; the main reason panels get upgradedLower; often no new heat-strip circuit
Gas serviceCan be closed if no other gas appliances remainStays
ControlsHeat pump thermostat with backup stageDual-fuel control with an outdoor switch point

The gas line: cap it, keep it, or remove the service

Converting the furnace doesn't mean the gas has to go. Many homes keep gas for a water heater, a range, a dryer, or a fireplace. In that case the furnace branch is capped and the rest of the gas system stays as it is.

One detail gets missed often: in many older homes the gas water heater shares a vent with the furnace. When the furnace comes out, the water heater is left alone on a vent that was sized for two appliances. That vent needs to be checked and corrected as part of the job, not left for a later inspection to catch. Our furnace venting guide describes how these shared vents are set up.

If every gas appliance moves to electric, you can have the gas service removed. If PG&E is your gas utility, its residential project resources page says gas service removal is requested through its Your Projects portal, with permits uploaded if they apply; a PG&E job owner contacts you within five business days, and review should finish within 66 calendar days of submission. PG&E says the service pipe is cut as close as possible to the main and both ends capped, and that customers are responsible for trenching and permit costs. If you only need gas service stopped and the meter removed, PG&E lists a separate phone request.

The duct check before anything is ordered

A gas furnace pushes warm air at a higher temperature than a heat pump does. A heat pump delivers comfortable heat with more airflow and somewhat cooler supply air, so ducts that were marginal for the furnace can show up as weak rooms or noisy registers after a conversion. The same ducts also carry summer cooling, so any restriction costs you in both seasons.

Before equipment is sized, the ducts should be looked at for size, leakage, insulation, and crushed or disconnected runs, especially in attics. Under California's Energy Code, an HVAC changeout typically includes duct leakage testing, and our duct leakage test guide explains what the rater measures and what happens if the ducts fail. The ductwork guide covers repair versus replacement.

Sizing should come from a room-by-room load calculation for both heating and cooling, not from the old furnace's input rating or the old AC's tonnage. A furnace was sized for heat only; a heat pump has to cover the summer peak too.

How the path differs by electric utility

Your mailing city doesn't decide which programs apply. The name on your electric bill does. The equipment work is the same everywhere; what changes is incentives, who you coordinate service changes with, and which local programs exist. Here is how the three electric utilities in our area compare, as we read their pages on November 12, 2026.

Conversion path by electric utility (checked 2026-11-12)
Electric utilityTypical areasHeat pump HVAC incentiveWhat to do
SMUDMost of Sacramento County, including Sacramento, Arden Arcade, McClellan Park and Orangevale; small parts of Placer and YoloGas-to-electric heat pump HVAC rebates and Go Electric panel and circuit rebatesUse a SMUD Contractor Network installer and read the SMUD rebate guide
Roseville ElectricCity of RosevilleNone listed on the city's residential rebates pageRead the Roseville rebate status page; consider PowerFlex for the thermostat
PG&E (with Pioneer or Valley Clean Energy generation)Placer foothills and much of Placer County outside Roseville, such as Rocklin; Davis, Woodland, Winters and unincorporated YoloNone listed on PG&E's residential rebates pageUse Pioneer's Incentive Finder or Valley Clean Energy's Electric Advisor; coordinate service changes with PG&E

SMUD territory: a conversion built around the rebate rules

SMUD describes its territory as about 900 square miles covering most of Sacramento County, with small adjoining parts of Placer and Yolo counties. If that's you, SMUD's heating and cooling rebates page is the most generous local program for a gas-to-electric conversion, and its rules shape the job:

  • The heat pump must be two-stage or variable-stage. Single-stage equipment doesn't qualify.
  • It must be installed by a participating contractor in the SMUD Contractor Network, who handles the rebate application.
  • The installation must pass Title 24 through a HERS CF3R, with any new ductwork insulated to at least R-8.
  • A Wi-Fi enabled, 7-day programmable connected thermostat is required.
  • SMUD's Go Electric meter panel, subpanel, and circuit rebates require a gas-to-electric conversion, which matters if your conversion needs electrical work.
  • SMUD's page doesn't say how dual-fuel systems are treated. If you're leaning toward keeping the furnace as backup, confirm with SMUD and the contractor which rebate tier, if any, applies before you sign.

Roseville Electric: no utility heat pump rebate listed

Inside the City of Roseville, power comes from Roseville Electric, the city's own utility. As of November 12, 2026, its residential rebates page lists EV rebates, PowerFlex, Home Energy Reports, seasonal tips, and solar. It doesn't list a heat pump HVAC rebate or a panel rebate. SMUD's rebates don't apply to Roseville Electric customers.

That changes the planning more than the work. Without a rebate tier to hit, the equipment choice can follow comfort, operating cost, and your panel's capacity. A dual-fuel setup, for example, may make more sense here if it avoids a panel upgrade. If you install a compatible smart thermostat, Roseville Electric's PowerFlex program is open to residential customers with an active account in their name, on a first-come, first-served basis. Our Roseville Electric rebate guide tracks the program list.

PG&E areas: Placer foothills, Rocklin, Davis and Yolo

Outside SMUD and Roseville Electric territory, PG&E delivers the power. Many of these homes also buy their electricity generation from a community choice aggregator: PG&E lists Pioneer Community Energy for Placer County, and Valley Clean Energy for Davis, Woodland, Winters and unincorporated Yolo County. PG&E says it keeps delivering electricity, metering, billing, maintenance and outage response for these customers.

We checked PG&E's residential rebates and incentives page on November 12, 2026, and it doesn't list a heat pump HVAC rebate. For local incentives, each aggregator points to a lookup tool rather than a fixed rebate. Pioneer launched an Incentive Finder in December 2025 that shows federal, state, and local incentives based on your location and income. Valley Clean Energy offers a free Electric Advisor service that helps homeowners compare electric upgrades, including heat pump HVAC, estimate costs and incentives, and connect with contractors.

Electrical work is where PG&E territory differs in practice. Changes to existing electric service, including a panel replacement or upgrade, are requested through PG&E's Your Projects portal. PG&E's residential project page says it covers the cost of replacing distribution transformers for panel upgrades, and that a panel change that increases service size may need a temporary disconnect that takes about 30 business days to schedule. If your conversion needs more service capacity, build that lead time into the plan.

State and federal incentives in 2026

Two incentives that used to stack with utility rebates aren't available for a typical 2026 conversion. The federal Section 25C energy efficient home improvement credit ended: the IRS says it applies to property placed in service before December 31, 2025. TECH Clean California says single-family HEEHRA rebates in Northern California have been fully reserved since February 24, 2026; new reservations go on a waitlist, and a waitlisted project is only eligible if the heat pump is installed after the reservation is approved.

For the current list of what still applies, see our rebate navigation guide.

Permits and HERS (now ECC) field verification

A conversion needs a mechanical permit from your city or county building department, and electrical work on the panel or new circuits is part of the same permitted project or a related one. The permit is what triggers the required field verification. The California Energy Commission says properly permitted work will trigger any necessary HERS testing, and that changing the HVAC system is the kind of alteration where that testing may be mandatory.

The name changed with the 2025 Energy Code. The CEC's Energy Code Compliance (ECC) Program took over field verification and diagnostic testing from the HERS Program, and HERS raters are now recognized as ECC-Raters with their certifications intact. You'll see both terms on forms and quotes for a while. The installing contractor and the ECC-Rater perform the testing, the CEC notes that urgent HVAC changeouts may register their certificates later but before the permit is closed, and group sampling for alterations has been removed, so your home is tested on its own. The completed documentation must be left in the home for the owner.

The CEC also says a homeowner has the right to hire a rater who is independent of the contractor. Most homeowners let the contractor arrange the rater, which is fine; the point is that the rater checks the contractor's work, and the result belongs to you.

A realistic sequence, start to finish

Conversions take longer than a straight AC swap because more parties are involved. The order below is what keeps surprises to a minimum. Install day itself is the short part; the electrical and utility steps are what stretch the calendar.

  • 1. Confirm your utility and incentives. Check the name on your electric bill, then read the matching rebate guide before you get quotes, so every quote is built to the same rules.
  • 2. Home assessment. Load calculation, duct inspection, panel review, gas appliance inventory, and a look at the outdoor unit location.
  • 3. Choose the path. Full electrification or dual fuel, equipment stage, and whether the panel or service needs an upgrade.
  • 4. Utility applications, if needed. A service upgrade or gas service removal goes to the utility early, because those reviews run on the utility's schedule, not the contractor's.
  • 5. Permits pulled. Mechanical, and electrical where the panel or circuits change.
  • 6. Installation. Electrical work, furnace removal or coil install, outdoor unit, line set, duct corrections, gas cap, thermostat, and startup.
  • 7. ECC-Rater verification and inspection. Duct leakage and the other required tests, then the city or county inspection to close the permit.
  • 8. Rebate paperwork and follow-up. In SMUD territory, the network contractor submits the rebate. Keep the permit, test certificates, and equipment documents together.

Questions to ask any contractor about a conversion

A conversion quote should answer more than a replacement quote does. These questions separate a thought-through conversion from an AC swap with a new label:

  • Did you do a room-by-room load calculation for heating and cooling, and can I see it?
  • Are you quoting full electrification or dual fuel, and why that one for my house?
  • What size are the backup heat strips, if any, and does my panel have capacity for them without an upgrade?
  • Does the job need a new 240-volt circuit, a subpanel, a panel upgrade, or a service upgrade, and who handles the utility side?
  • What happens to my water heater's vent once the furnace comes out?
  • Are you reusing the line set and ducts, and what did you find when you checked them?
  • Which thermostat or dual-fuel control is included, and is it compatible with my utility's programs?
  • Who pulls the permits, who schedules the ECC-Rater, and what happens if the duct test fails?
  • If I'm a SMUD customer, are you listed in the SMUD Contractor Network, and which rebate tier does this equipment meet?

Common questions

Do I have to remove my gas service when I switch to a heat pump?

No. Only the furnace's gas branch is capped. If a water heater, range, dryer, or fireplace still uses gas, the service stays. Gas service removal is an option only once every gas appliance has moved to electric.

Can I keep my gas furnace as backup?

Yes. A dual-fuel setup keeps the furnace and adds a heat pump with a matched coil and a control that switches between them at a set outdoor temperature. In SMUD territory, confirm how a dual-fuel system is treated for rebates before you commit, because SMUD's page doesn't address it.

Will I need a panel upgrade?

Not always. The added load is mostly the electric air handler and any backup heat strips. A load calculation answers the question. A dual-fuel setup or smaller strips can sometimes avoid an upgrade, and in SMUD territory the Go Electric rebates cover panel, subpanel and circuit work when it's part of a gas-to-electric conversion.

What is an ECC-Rater, and is it the same as a HERS rater?

Yes, it's the same role under a new name. With the 2025 Energy Code, the CEC moved field verification and diagnostic testing into its Energy Code Compliance Program, and HERS raters are now recognized as ECC-Raters. They verify things like duct leakage after the install so the permit can close.

Is there a federal tax credit for a heat pump conversion in 2026?

No. The Section 25C energy efficient home improvement credit ended; the IRS says it covers property placed in service before December 31, 2025. Utility rebates, where your utility offers them, are the main incentive for a 2026 conversion.

Does California require me to convert to a heat pump when my furnace fails?

No statewide rule requires an existing home to switch. The 2025 Title 24 heat pump baseline is for new construction. A city or county can adopt a local reach code, so ask your building department if you want to be certain about your address.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service