Win a free furnace replacement. Apply by Dec 9
CSLB #1023360

Supporting article · 7-minute read · Last reviewed November 2026

High heating bills: what is driving the cost and how to bring it down

A sudden jump in your heating bill usually means the furnace is running more than it should. The most common causes are a clogged filter forcing the furnace to work harder, leaky ducts losing heated air before it reaches your rooms, thermostat settings that keep the furnace running around the clock, air leaks in the building envelope, and an aging furnace that has lost efficiency. PG&E notes that for every degree you set the thermostat above 68 degrees Fahrenheit, you use three to five percent more energy. Start with the filter, the thermostat, and duct inspections before assuming you need a new furnace.

Reviewed by Vasiliy BardadinOwner & Lead Technician, Statewide HVAC · CSLB #1023360

On this page · 8 sections
  1. 01How much should the furnace run in winter
  2. 02The most common causes
  3. 03The filter and airflow connection
  4. 04Duct leaks you cannot see
  5. 05Thermostat habits that cost more than you think
  6. 06When the furnace itself is the problem
  7. 07Sacramento-specific factors
  8. 08What you can do right now

How much should the furnace run in winter

There is no single right answer, because runtime depends on outdoor temperature, house size, insulation, and furnace capacity. But patterns matter. If the furnace ran two or three cycles per hour last winter and now it seems to run almost continuously, something has changed. Either the house is losing heat faster, the furnace is producing heat less effectively, or the thermostat is asking for more than it used to.

A bill that jumps by a large percentage from the same month the previous year, with similar weather, points to a mechanical or envelope problem. A bill that rises modestly in a colder-than-normal month is just the furnace doing its job.

The most common causes

Most high-bill complaints trace to one or more items on this list. Several of them overlap and compound each other.

Common causes of high heating bills and how to address them
CauseWhy it raises the billWhat to do
Clogged air filterRestricts airflow, forces the furnace to run longer cycles, and may trip the limit switch repeatedlyCheck and replace the filter monthly during the heating season
Duct leaksENERGY STAR estimates 20 to 30 percent of heated air can be lost through leaks before reaching roomsProfessional duct sealing and insulation; California HERS verification may apply
Thermostat set too high or scheduled poorlyEach degree above 68 degrees Fahrenheit uses three to five percent more energy according to PG&ESet to 68 degrees when home; use setback of 7 to 10 degrees when sleeping or away
Air leaks in the building envelopeCold air infiltrates through gaps around windows, doors, outlets, and penetrations, making the furnace run to compensateWeatherstripping, caulk, and blown-in insulation in the attic
Aging or poorly maintained furnaceDirty burners, a degraded heat exchanger, and worn parts reduce combustion efficiency over timeAnnual professional tune-up; consider replacement if the furnace is past 15 to 20 years
Oversized furnace short cyclingShort cycles are less efficient than steady runs because startup and shutdown waste fuel each timeCorrect sizing at replacement; a two-stage or modulating furnace improves part-load efficiency
Single-pane windows or missing insulationHeat leaves the house faster than the furnace can replace it, driving long runtimesWindow upgrades, attic insulation, and wall insulation where feasible

The filter and airflow connection

A dirty filter is the cheapest and most overlooked cause of high bills. When the filter is clogged, the blower has to work harder to push air through, and the heat exchanger gets hotter than designed because there is not enough air moving across it. The limit switch may trip, shutting the burners off early and forcing another startup cycle. Every restart wastes a small amount of gas during ignition and heat-up.

SMUD recommends replacing the filter every one to three months and notes that a system with dirty filters can use five to ten percent more energy. During the heating season, check it monthly. Our filter and airflow guide explains how filter type and MERV rating affect static pressure and efficiency.

Duct leaks you cannot see

ENERGY STAR states that leaky ducts can reduce heating and cooling system efficiency by as much as 20 percent. In homes where ductwork runs through an unconditioned attic or crawlspace, the loss may be higher because leaked air goes directly into an unheated space.

Ducts also lose heat through their walls even when they do not leak. Uninsulated sheet-metal ducts in an attic can radiate heat before the air reaches the register. Adding duct insulation and sealing joints with mastic addresses both problems. Our duct insulation guide covers the R-6 versus R-8 decision, and professional duct sealing includes before-and-after leakage testing.

Thermostat habits that cost more than you think

PG&E advises setting the furnace thermostat to 68 degrees Fahrenheit or lower, health permitting, and notes that three to five percent more energy is used for each degree above 68. The U.S. Department of Energy estimates that turning the thermostat back 7 to 10 degrees for eight hours a day can save as much as 10 percent per year on heating and cooling.

A programmable or smart thermostat automates those setbacks. ENERGY STAR certified smart thermostats save an average of about 8 percent on heating and cooling bills based on EPA-verified real-world field data. But the savings only happen if the schedule is set and not constantly overridden. See our winter thermostat settings guide for specific setpoint recommendations.

The fan setting matters too. Leaving the fan on ON instead of AUTO keeps the blower running around the clock. That adds electricity cost and, in winter, pushes cooler air through the ducts between heating cycles, which can make the house feel cold and prompt someone to raise the setpoint.

When the furnace itself is the problem

Furnace efficiency is measured by AFUE, the percentage of fuel that becomes useful heat. A 20-year-old furnace may be rated at 80 percent AFUE, meaning 20 percent of the fuel goes up the flue. A modern condensing furnace achieves 95 to 98 percent AFUE. The difference compounds over a full heating season.

Even within its rated efficiency, a furnace loses performance as it ages. Dirty burners, a corroded heat exchanger, a worn blower motor, and a degraded gas valve all reduce output. A professional tune-up restores what can be restored. If the furnace is past its useful life, replacement with a right-sized, higher-efficiency unit is usually a better investment than ongoing repairs. Our furnace hub covers the repair-versus-replace decision.

Sacramento-specific factors

On the valley floor, the heating season is short and mild, but many homes were built with single-pane windows and minimal insulation because cooling was the priority. When temperatures drop into the 30s on tule-fog mornings, those homes lose heat fast and the furnace runs long cycles.

Foothill homes at higher elevations have a colder, longer heating season and some are on propane instead of PG&E natural gas. Propane costs more per therm than natural gas, so the same runtime produces a bigger bill. Ensuring the furnace is sized and tuned for its fuel type and elevation matters more up the hill.

Regardless of location, checking your PG&E or SMUD account for a comparison to the same billing period last year isolates whether the jump is weather-driven or equipment-driven. A year-over-year increase with similar temperatures is the clearest sign something mechanical has changed. Visit our heating hub for seasonal maintenance steps that help prevent bill surprises.

What you can do right now

Before calling for service, run through these no-cost and low-cost steps:

  • Replace the filter if it has been more than a month since the last change.
  • Set the thermostat to 68 degrees when home and drop it 7 to 10 degrees at night or when away. Use a schedule if the thermostat supports one.
  • Set the fan to AUTO, not ON.
  • Open all supply registers and make sure return grilles are clear.
  • Walk through the attic or crawlspace and look for disconnected or crushed ducts. Feel for air leaking at duct joints.
  • Check weatherstripping around exterior doors and caulk around windows. Seal obvious gaps.
  • Compare this month's bill to the same month last year on your utility's website to see whether the increase is weather-related or mechanical.

Common questions

How much can a dirty filter raise my heating bill?

SMUD estimates that a furnace with dirty filters can use five to ten percent more energy. The clogged filter forces longer run cycles and may cause the furnace to short cycle, wasting gas on repeated startups.

What thermostat setting saves the most on heating?

PG&E recommends 68 degrees Fahrenheit or lower when home, and the U.S. Department of Energy says a setback of 7 to 10 degrees for eight hours a day can save up to 10 percent per year. Lower is better, health permitting.

Can leaky ducts really increase my heating bill?

Yes. ENERGY STAR reports that 20 to 30 percent of heated air can be lost to duct leaks in a typical house, and that leaky ducts can reduce system efficiency by as much as 20 percent. Professional duct sealing is one of the highest-return efficiency improvements.

Is it cheaper to keep the thermostat at one temperature or use setbacks?

Setbacks save money. The DOE estimates up to 10 percent savings from an 8-hour daily setback of 7 to 10 degrees. Keeping the furnace at a constant high temperature means it runs whenever the house loses heat, which in cold weather is almost all the time.

Does a furnace lose efficiency as it ages?

Yes. Dirty burners, worn parts, and heat-exchanger degradation reduce output over time even if the rated AFUE has not changed. An annual tune-up helps, but a furnace past 15 to 20 years is unlikely to match its original efficiency.

Will a new furnace cut my bill in half?

It depends on the old furnace's condition and rated efficiency. Replacing an 80-percent-AFUE furnace with a 96-percent unit saves roughly 17 percent of fuel on heating alone. That is meaningful but not half. Duct sealing, insulation, and thermostat management often close the gap further.

Should I switch from a furnace to a heat pump to save on heating?

A heat pump can reduce heating costs in the Sacramento region because it moves heat instead of generating it from combustion. The savings depend on electricity rates, gas rates, and the heat pump's efficiency. Our heat-pump-versus-furnace guide covers the comparison in detail.

Sources

Program amounts and rules change. Confirm current terms with the source before you rely on them.

Reviewed and published by Statewide HVAC

Vasiliy Bardadin, owner and lead technician of Statewide HVAC, standing outdoors in a white Statewide HVAC polo.

Vasiliy Bardadin

Owner & Lead Technician

Statewide HVAC is owner-operated and Roseville-based.

Statewide HVAC is a CSLB-licensed heating and air conditioning contractor (#1023360) serving the Sacramento region from Roseville. Our guides are written for local homeowners, list their sources, and show the date they were last reviewed. About us

Questions this guide didn't cover?

We'll answer them on your project — no sales pressure.

(916) 461-3405Request Service